RFR(S): 8059334: nsk/jvmti/scenarios/hotswap/HS201/hs201t001 fails with exit code 0 after timeout
dean.long at oracle.com
dean.long at oracle.com
Sat Nov 4 04:44:20 UTC 2017
I'm not an expert in this area of code, but I'm wondering about
Vladimir's comment about ciEnv::jvmti_state_changed() in the bug
report. With your fix, maybe we don't need to check
ciEnv::jvmti_state_changed() (which doesn't seem to be enough by itself)
and throw away the compiled result. We could just keep it around so it
can be used when "interp only" mode is switched off.
On 11/3/17 5:25 PM, Chris Plummer wrote:
> Please review the following:
> The CR is closed, so I'll try to explain the issue here. The very
> short explanation is that the JVMTI test was enabling SINGLE STEP and
> doing a PopFrame, but the test method managed to get compiled and
> started executing compiled after the thread was put in "interp only"
> mode (which should never happen) and before the PopFrame was
> processed. The cause is a lack of a check for "interp only" mode in
> the OSR related compilation policy code.
> The test is testing JVMTI PopFrame support. The test thread has a
> small method that sits in a tight loop. It will never exit. The main
> thread enables SINGLE STEP on the test thread, and then does a
> PopFrame on the test thread to force it out of the looping method.
> When the test failed due to a time out, I noticed it was still stuck
> in the small method, even though a PopFrame had been requested.
> Further, I noticed the method was compiled, so there was no chance the
> method would ever detect that it should do a PopFrame. Since "interp
> only" mode for SINGLE STEP had been enabled, the method should not be
> running compiled, so clearly something went wrong that allowed it to
> compile and execute.
> When SINGLE STEP is requested, JVMTI will deopt the topmost method
> (actually the top 2), put the thread in "interp only" mode, and then
> has checks to make sure the thread continues to execute interpreted.
> To avoid compilation when a back branch tries to trigger one, there is
> a check for "interp only" mode in SimpleThresholdPolicy::event(). If
> the thread is in "interp only" mode, it will prevent compilation.
> SimpleThresholdPolicy::event() is called (indirectly) by
> InterpreterRuntime::frequency_counter_overflow(), which is called from
> the interpreter when the back branch threshold is reached.
> After some debugging I noticed when the test timeout happens, "interp
> only" mode is not yet enabled when
> InterpreterRuntime::frequency_counter_overflow() is called, but is
> enabled by the time InterpreterRuntime::frequency_counter_overflow()
> has done the lookup of the nm. So there is a race here allowing the
> thread to begin execution in a compiled method even though "interp
> only" mode is enabled. I think the reason is because we safepoint
> during the compilation, and this allows a SINGLE STEP request to be
> processed, which enables "interp only" mode.
> I should add that initially I only saw this bug with -Xcomp, but
> eventually realized it was caused by disabling BackgroundCompilation.
> That makes it much more likely that a SINGLE STEP request will come in
> and be processed during the call to
> InterpreterRuntime::frequency_counter_overflow() (because it will
> block until the compilation completes).
> I believe for the fix it is enough just to add an "interp only" mode
> check in InterpreterRuntime::frequency_counter_overflow() after the nm
> lookup, and set it nm to NULL if we are now in "interp only" mode. If
> we are not in "interp only" mode at this point (and start executing
> the compiled method) it should not be possible to enter "interp only"
> mode until we reach a safepoint at some later time, and at that point
> the method will be properly deopt so it can execute interpreted.
More information about the hotspot-compiler-dev